10/23/2021 0 Comments Ubuntu Mac Os Emulator
MicroM8 is available to download for WIndows, macOS / OSX and Linux and its free To play and upcycle classic 8-bit games using 3D graphics and more. Windows x64 Windows x86 Mac OS X Android Ubuntu 13.04: 4.0-658.
![]() ![]() Ubuntu Emulator Mac OS X AndroidNow you should be ready to go.If you get mol module not found errors, try insmodding it manually insmod /lib/modules/2.6.(your kernel version)-powerpc/misc/mol.koIf OSX doesn't start, edit the blkdev settings in /etc/mol/molrc.osx. Mine was given as follows: 6: tun0: mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 100Inet6 fe80::d868:17ff:fe7b:32c1/64 scope linkIn OS X, then set up the en3 network port manually, by allocating an appropriate IP (in my case 192.168.40.2 was a good choice), set Router and DNS server to the ip associated with your tun0 interface in linux (192.168.40.1) and the subnet mask to 255.255.255.0. Once you have completed the setup, run ip addr to check the ip address for the tun0 interface. Make sure that en3 is set to configure with DHCP.Now open up Safari or Firefox, and if you are lucky you should have a web connection.Do as above, but without installing dhcpd. MOL creates a network tunnel called tun0 at the Linux end, and en3 on the Mac OS X end.Once you have logged into to Mac OS X open up the system preferences. CTRL + ALT + F7 should take you back to your Linux desktop.If you want mol to always start full screen, edit /etc/mol/molrc.video and change enable_xvideo: yes to enable_xvideo: noSee its manpage for more usage information.If you are using mol to use the iTunes music store, or watch flash on the web, then you will need to get networking running.You will need to install ipmasq, dnsmasq and dhcpd using synaptic orSudo apt-get install ipmasq dnsmasq dhcpdThen enable dhcp for the tun0 interface that mol uses, in /etc/default/dhcp, put the lineAnd in /etc/mol/tunconfig at the bottom just beforeNow run startmol -osx, and we can set up the network on the Mac OS X side. You can user uname -r to determine your version. 1) Download the latest kernel source. To do that, I am providing my notes below.To run Tiger and Eliminate Annoying Sluggish Behavior on MOL Install this Patched VersionThanks to folks on the MOL mailing list for these tips. Afterwards, the response was more snappy.) The real fix is to use a more recent version of Mac-on-Linux though. (Before I did this I was unable to even double click. Then you need to go to the sound control panel and enable the MOL Audio for output. Microsoft office 2017 for mac downloadActually, I had better luck on the networking setup with the sheep driver. Look for the latest mol version he has provided.6) Set up and start MOL using the instructions in the section above. 3) Download the patched MOL that Joe Jezak has kindly provided. You can also use the synaptic package manager or Adept to do this.2) Follow the instructions on this Wiki for building the kernel found at. You will need to do this as root. If I figure that out, I'll append this note.If you start MoL to boot OS X and get an error that looks like this: > -> Boot loader failure: Out of memoryThen you need to install the new boot loader.3) Copy the file into /usr/share/mol/drivers/. With this setting Tiger boots and gets an IP address via dhcp from my local wireless router.A side note: I have not been able to boot an OS 9 partition with this setup and there have been some similar notes on a Yellow Dog Linux forum.
0 Comments
Leave a Reply. |
AuthorJody ArchivesCategories |